Alpha HL Series

Alpha HL Series

The HL resistor series from Alpha Electronics offers their ultra-precision resistor capabilities in a hermetically sealed package all with a zero-TCR. With a resistance range from 100Ω up to 100kΩ all in a small through-hole package with a pin pitch of 5.08 ±0.25mm. By utilising Alpha's Bulk Metal® foil resistor technology, they are able to produce resistors with a zero-TCR (0±15 ppm/°C between 0°C and +50°C) and excellent long-term stability.

  • Ultra-precision hermetically sealed resistor
  • Available in any resistance between 100Ω and 100kΩ
  • Through-hole package with a pin pitch of 5.08 ±0.25mm
  • Tight tolerance options as low as ±0.005% available for resistances between 30Ω and 120kΩ
  • Characteristic S Zero-TCR (0±15 ppm/°C from 0°C up to +50°C)
  • Maximum working voltage of 300V
  • Power rating of 0.3W (at +70°C)
  • Maximum rated operating temperature +70°C
  • Working temperature from -65°C up to +150°C

The Alpha Electronics HL hermetically sealed ultra-precision resistor series have been designed with longer leads to ensure the correct clearance from the PCB is achieved when soldering. It is advised that the resistors are kept over 10mm away from the board surface by using an insulating tube.


The below table gives a summary of the specifications available for each resistor model including the Alpha HL series:

Alpha HC Specifications

* Symbols parenthesized are for part number composition
✝ Resistance figures are obtained by measuring the leads at point 12.7 ±3.2mm away from the root

Specifications
Additional Features
  • Ultra-precision through-hole resistor
  • Zero-TCR ultra-precision resistor
  • Hermetically sealed package
  • Pin pitch of 5.08 ±0.25mm
  • Maximum working voltage of 300V
  • Working temperature range of -65°C to +150°C
  • Maximum rated operating temperature of +70°C
Maximum Power Rating
  • 0.3W (at +70°C)
Maximum Resistance
  • 100kΩ
Minimum Resistance
  • 100Ω
TCR
  • Characteristic S (0±15 ppm/°C between 0°C and +50°C)
Tolerance
  • ±0.005% (V)
  • ±0.01% (T)
  • ±0.02% (Q)
  • ±0.05% (A)
  • ±0.1% (B)
  • ±0.5% (D)
  • ±1.0% (F)

We are pleased to provide you with a range of additional content including videos, product datasheets, case studies, white papers and application notes for your reference. Please see below for the latest content available:

 

 

DOCUMENTATION
PDF DocumentAlpha Electronics HK and HL zero-TCR hermetically sealed ultra-precision resistor series datasheet
PDF DocumentAlpha Electronics manufacturing process, adjustment of resistance value construction, and temperature characteristics of resistance information which covers their resistor range including typical characteristics such as their typical 0.14 ppm/°C TCR
PDF DocumentAlpha Electronics additional services and custom products available to compliment their precision and ultra-precision resistor ranges
PDF DocumentAlpha Electronics ultra-precision resistors databook, covering all parts and models they have to offer

 

 

 

VIDEOS
Resistor Stability Put to the Test (Demo Video)

In this video, host Richard Zuratt from VPG puts the stability of the three major resistor technologies — foil, thin, and thick film — to the test. Each resistor type is subjected to an overload pulse and its change in resistance value is recorded. Due to the homogeneous nature of the VPG Bulk Metal® Foil resistor, it is the only of the three to experience no change from the high power pulse. This demonstrated performance makes foil resistors the technology of choice for critical applications where long-term stability and survivability are paramount.
A head to head comparison of the survival rates of precision thin film nichrome (NiCr) resistors versus VFR Bulk Metal Foil resistors in a high humidity environment.

All resistors that are based on nichrome, which is a category that includes both thin film devices and Bulk Metal Foil resistors, are susceptible to electro-chemical corrosion or etching when placed in a high humidity environment and powered with a very low wattage. But since the nichrome element of a Bulk Metal Foil resistor is hundreds of times thicker than the element in a thin film device with the same value, it will last much longer under these conditions. This video shows the actual etching process and survival times for thin film and foil nichrome resistive elements as they are tested in 100% humidity conditions.
Comparison Testing of Chip Resistor Technologies Under High Vibration

Surface-mount resistors suffer physical stresses when exposed to high vibration or thermally unstable environments. Failure modes commonly occur in welds, solder joints, connectors, and terminations, ultimately resulting in circuit failure. In this demonstration, vibration-table-mounted boards are subjected to ±2° deflection 25 times per second and monitored for any ΔR > 0.1%. All the chip resistors failed in 2 to 12 minutes (8K to 16K cycles). But the Alpha MPP molded Bulk Metal® Z-Foil resistor with flexible terminations experienced over a million cycles with no change in resistance.
VIDEOS
Resistor Stability Put to the Test (Demo Video)

In this video, host Richard Zuratt from VPG puts the stability of the three major resistor technologies — foil, thin, and thick film — to the test. Each resistor type is subjected to an overload pulse and its change in resistance value is recorded. Due to the homogeneous nature of the VPG Bulk Metal® Foil resistor, it is the only of the three to experience no change from the high power pulse. This demonstrated performance makes foil resistors the technology of choice for critical applications where long-term stability and survivability are paramount.
A head to head comparison of the survival rates of precision thin film nichrome (NiCr) resistors versus VFR Bulk Metal Foil resistors in a high humidity environment.

All resistors that are based on nichrome, which is a category that includes both thin film devices and Bulk Metal Foil resistors, are susceptible to electro-chemical corrosion or etching when placed in a high humidity environment and powered with a very low wattage. But since the nichrome element of a Bulk Metal Foil resistor is hundreds of times thicker than the element in a thin film device with the same value, it will last much longer under these conditions. This video shows the actual etching process and survival times for thin film and foil nichrome resistive elements as they are tested in 100% humidity conditions.
Comparison Testing of Chip Resistor Technologies Under High Vibration

Surface-mount resistors suffer physical stresses when exposed to high vibration or thermally unstable environments. Failure modes commonly occur in welds, solder joints, connectors, and terminations, ultimately resulting in circuit failure. In this demonstration, vibration-table-mounted boards are subjected to ±2° deflection 25 times per second and monitored for any ΔR > 0.1%. All the chip resistors failed in 2 to 12 minutes (8K to 16K cycles). But the Alpha MPP molded Bulk Metal® Z-Foil resistor with flexible terminations experienced over a million cycles with no change in resistance.

RoHS Compliance

This product is available fully compliant to the RoHS EU directive 2011/65/EU.

  • Views: 193
  • Product Code: Alpha HL Series
  • SKU: Alpha HL Series
  • Availability: In Stock
0 Product(s) Sold
  • £0.00
  • Ex Tax: £0.00

Available Options