Gear Tooth Sensors & Encoders

Gear Tooth Sensors & Encoders
Show:
Sort By:

NVE ABL004-00E

The NVE ABL004-00E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 1mm for use with a recommended gear pitch of between 2.5mm and 6mm and an operating frequency of 1MHz. The ABL004 series from NVE have differential sensor elements that provide sinusoidal outputs and is a single bridge sensor producing a sinusoidal wave form at the output.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Single bridge 1mm element spacing
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package

The NVE ABL004-00E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL004-00E

NVE ABL004-00E Specifications

£0.00 Ex Tax: £0.00

NVE ABL004-10E

The NVE ABL004-10E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 1mm for use with a recommended gear pitch of between 2.5mm and 6mm and an operating frequency of 1MHz. The ABL004 series from NVE have differential sensor elements that provide sinusoidal outputs and is a single bridge sensor producing a sinusoidal wave form at the output.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Single bridge 1mm element spacing
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • TDFN6 Package

The NVE ABL004-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL004-10E

NVE ABL004-10E Specifications

£0.00 Ex Tax: £0.00

NVE ABL005-00E

The NVE ABL005-00E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.5mm for use with a recommended gear pitch of between 1.5mm and 2.5mm, and an operating frequency of 1MHz. The ABL005 series from NVE have differential sensor elements that provide sinusoidal outputs and is a single bridge sensor producing a sinusoidal wave form at the output.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Single bridge with 0.5mm element spacing
  • Operating frequency of 1MHz
  • Operating temperature range -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package

The NVE ABL005-00E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL005-00E

NVE ABL005-00E Specifications

£0.00 Ex Tax: £0.00

NVE ABL005-10E

The NVE ABL005-10E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.5mm for use with a recommended gear pitch of between 1.5mm and 2.5mm and an operating frequency of 1MHz. The ABL005 series from NVE have differential sensor elements that provide sinusoidal outputs and is a single bridge sensor producing a sinusoidal wave form at the output.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Single bridge with 0.5mm element spacing
  • Operating frequency of 1MHz
  • Operating temperature range -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • TDFN6 Package

The NVE ABL005-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL005-10E

NVE ABL005-10E Specifications

£0.00 Ex Tax: £0.00

NVE ABL006-00E

The NVE ABL006-00E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.3mm for use with a recommended gear pitch of between 0.6mm and 1.5mm and an operating frequency of 1MHz. The ABL006 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a single bridge sensor producing a sinusoidal wave form at the output.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Single bridge with 0.3mm element spacing
  • Gear pitch between 0.6mm and 1.5mm
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package type

The NVE ABL006-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL006-00E

NVE ABL006-00E Specifications

£0.00 Ex Tax: £0.00

NVE ABL006-10E

The NVE ABL006-10E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.3mm for use with a recommended gear pitch of between 0.6mm and 1.5mm and an operating frequency of 1MHz. The ABL006 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a single bridge sensor producing a sinusoidal wave form at the output.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Single bridge with 0.3mm element spacing
  • Gear pitch between 0.6mm and 1.5mm
  • Operating frequency of 1MHz
  • Operating temperature range -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • TDFN6 Package type

The NVE ABL006-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL006-10E

NVE ABL006-10E Specifications

£0.00 Ex Tax: £0.00

NVE ABL014-00E

The NVE ABL014-00E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 1mm for use with a recommended gear pitch of between 2.5mm and 6mm and an operating frequency of 1MHz. The ABL014 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a Dual-bridge sensor producing sine and cosine waveforms at the output to provide gear tooth direction information.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Dual bridge with 1mm element spacing
  • Gear pitch between 2.5mm and 6mm
  • 0.5mm phase shift between sine and cosine outputs
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package type

The NVE ABL014-00E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL014-00E

NVE ABL014-00E Specifications

£0.00 Ex Tax: £0.00

NVE ABL014-10E

The NVE ABL014-10E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 1mm for use with a recommended gear pitch between 2.5mm and 6mm and an operating frequency of 1MHz. The ABL014 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a Dual-bridge sensor producing sine and cosine waveforms at the output to provide gear tooth direction information.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Dual bridge with 1mm element spacing
  • Gear pitch between 2.5mm and 6mm
  • 0.5mm phase shift between sine and cosine outputs
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package type

The NVE ABL014-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL014-10E

NVE ABL014-10E Specifications

£0.00 Ex Tax: £0.00

NVE ABL015-00E

The NVE ABL015-00E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.5mm for use with a recommended gear pitch of between 1.5mm to 2.5mm and an operating frequency of 1MHz. The ABL015 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a dual bridge sensor producing sine and cosine waveforms at the output to provide gear tooth direction information.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Dual bridge with 0.5mm element spacing
  • Gear pitch between 1.5mm and 2.5mm
  • 0.25mm phase shift between sine and cosine outputs
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package type

The NVE ABL015-00E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL015-00E

NVE ABL015-00E Specifications

£0.00 Ex Tax: £0.00

NVE ABL015-10E

The NVE ABL015-10E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.5mm for use with a recommended gear pitch between 1.5mm and 2.5mm with an operating frequency of 1MHz. The ABL015 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a Dual-bridge sensor producing sine and cosine waveforms at the output to provide gear tooth direction information.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Dual bridge with 0.5mm element spacing
  • Gear pitch between 1.5mm and 2.5mm
  • 0.25mm phase shift between sine and cosine outputs
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • TDFN6 Package type

The NVE ABL015-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL015-10E

NVE ABL015-10E Specifications

£0.00 Ex Tax: £0.00

NVE ABL016-00E

The NVE ABL016-00E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.3mm for use with a recommended gear pitch between 0.6mm to 1.5mm and an operating frequency of 1MHz. The ABL016 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a dual bridge sensor producing sine and cosine waveforms at the output to provide gear tooth direction information.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Dual bridge with 0.3mm element spacing
  • Gear pitch between 0.6mm and 1.5mm
  • 0.15mm phase shift between sine and cosine outputs
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • MSOP8 Package type

The NVE ABL016-00E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL016-00E

NVE ABL016-00E Specifications

£0.00 Ex Tax: £0.00

NVE ABL016-10E

The NVE ABL016-10E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.3mm for use with a recommended gear pitch between 0.6mm to 1.5mm and an operating frequency of 1MHz. The ABL016 series from NVE uses differential sensor elements that provide sinusoidal outputs and is a dual bridge sensor producing sine and cosine waveforms at the output to provide gear tooth direction information.

  • GMR analog gear tooth sensor
  • Wide airgap
  • Large analog peak-to-peak output
  • Dual bridge with 0.3mm element spacing
  • Gear pitch between 0.6mm and 1.5mm
  • 0.15mm phase shift between sine and cosine outputs
  • Operating frequency of 1MHz
  • Operating temperature range of -50°C to +150°C
  • Supply voltage range between 0V and 30V
  • Resistance range of 4kΩ to 7kΩ at +25°C
  • Saturation Field of 180Oe
  • TDFN6 Package type

The NVE ABL016-10E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE ABL series including the ABL016-10E

NVE ABL016-10E Specifications

£0.00 Ex Tax: £0.00

NVE AKL001-12E

The NVE AKL001-12E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 1mm for use with a recommended gear pitch of between 2.5mm and 6mm with an operating frequency up to 10kHz. The AKL-series sensors from NVE combine a sensor bridge with integrated signal processing to provide a 50% duty cycle digital output. Integrated signal processing includes gain and offset normalization. AKL-Series sensors are configured as two wire devices, where the supply current indicates passing teeth.

  • GMR analog gear tooth sensor
  • Airgap of 1mm to 3.5mm
  • Large analog peak-to-peak output
  • Single bridge with 1mm element spacing
  • Gear pitch between 2.5mm and 6mm
  • Operating frequency range from DC to 10kHz
  • Operating temperature range from -40°C to +150°C
  • Supply voltage range from +4.5V to 36V
  • Digital output duty cycle of 50%
  • TDFN8 Package type

The NVE AKL001-12E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE AKL series including the AKL001-12E

NVE AKL001-12E Specifications

£0.00 Ex Tax: £0.00

NVE AKL002-12E

The NVE AKL002-12E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.5mm for use with a recommended gear pitch between 1.5mm and 2.5mm with an operating frequency up to 10kHz. The AKL-series sensors from NVE combine a sensor bridge with integrated signal processing to provide a 50% duty cycle digital output. Integrated signal processing includes gain and offset normalization. AKL-Series sensors are configured as two wire devices, where the supply current indicates passing teeth.

  • GMR analog gear tooth sensor
  • Airgap of 1mm to 2.5mm
  • Large analog peak-to-peak output
  • Single bridge with 0.5mm element spacing
  • Operating frequency from DC to 10kHz
  • Gear pitch between 1.5mm and 2.5mm
  • Operating temperature range from -40°C to +150°C
  • Supply voltage range from +4.5V to 36V
  • Digital output duty cycle of 50%
  • TDFN8 Package type

The NVE AKL002-12E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE AKL series including the AKL002-12E

NVE AKL002-12E Specifications

£0.00 Ex Tax: £0.00

NVE AKL003-12E

The NVE AKL003-12E analog gear tooth sensors are versatile, wide airgap typically used with ferromagnetic gears and bias magnets. The sensor elements are spaced at 0.3mm for use with a recommended gear pitch between 0.6mm and 1.5mm with an operating frequency up to 10kHz. The AKL-series sensors from NVE combine a sensor bridge with integrated signal processing to provide a 50% duty cycle digital output. Integrated signal processing includes gain and offset normalization. AKL-Series sensors are configured as two wire devices, where the supply current indicates passing teeth.

  • GMR analog gear tooth sensor
  • Airgap between 1mm and 2mm
  • Large analog peak-to-peak output
  • Single bridge with 0.3mm element spacing
  • Operating frequency range from DC to 10kHz
  • Gear pitch of between 0.6mm and 1.5mm
  • Operating temperature range from -40°C to +150°C
  • Supply voltage range from +4.5V to 36V
  • Digital output duty cycle of 50%
  • TDFN8 Package type

The NVE AKL003-12E GMR analog gear tooth sensor covers the following applications:

  • Motion, speed, and position sensing
  • Linear and rotational encoders
  • Closed-loop servo systems
  • Automotive sensors

The below table gives the full specifications of the NVE AKL series including the AKL003-12E

NVE AKL003-12E Specifications

£0.00 Ex Tax: £0.00