Alpha MD Series

  • Alpha Electronics

Product Features

  • Ultra-precision transfer moulded resistor
  • Resistance range form 5Ω to 80kΩ
  • Tolerance from ±0.005% to ±1%
  • TCR of ±1 ppm/°C, ±2.5 ppm/°C or ±5 ppm/°C
  • Power rating of 0.125W (at 125°C)
  • Temperature range from -65°C up to +175°C

Applications

The MD ultra-precision transfer moulded resistor series from Alpha Electronics offers a wide resistance range from 5Ω up to 80kΩ with tight tolerances, all in a small through-hole package with a pin pitch of 5.08 ±0.25mm. By utilising Alpha’s Bulk Metal® foil resistor technology, they are able to produce resistors with low temperature coefficients and excellent long-term stability.

  • Ultra-precision transfer moulded resistor
  • Available in any resistance between 5Ω and 80kΩ
  • Transfer moulded through-hole package with a pin pitch of 5.08 ±0.25mm
  • Tight tolerance options as low as ±0.005% available for resistances between 30Ω and 80kΩ
  • Tight TCR options available of ±1 ppm/°C (from 0°C up to +65°C, between 100Ω and 80kΩ) or ±2.5 ppm/°C (from -55°C up to +125°C, between 30Ω and 80kΩ)
  • Maximum working voltage of 250V
  • Power rating of 0.125W (at +125°C)
  • Maximum rated operating temperature +125°C
  • Temperature range from -65°C up to +175°C

 

Alpha’s Bulk Metal® foil resistor technology means that these transfer moulded, through-hole, ultra-precision resistors are ideal for precision measurements, also their low inductance makes them ideal for use at higher frequencies.

These resistors are constructed using an outer coating of transfer moulded epoxy resin, making the parts strongly resistant to heat, moisture and solvents. Internally, there are secondary leads which act as a buffer so that stress on the exterior leads is not transmitted to the foil, providing stability against vibrations when the resistor is mounted on a circuit.

 

The below table gives the full specifications for each resistor model available including the Alpha MD series:

Alpha MD Specifications
* Symbols parenthesized are for part number composition
✝ Resistance figures are the values obtained by measuring the leads at point 12.7±3.2mm away from the base for type MB, MC and MD, but, in case of resistance below 10Ω, the value at 1.6 ±0.6mm away from the base for all types
** Temperature characteristic Z is applicable for temperature range between 0°C and +60°C

 

Clear
Quantity
Calculators and Convertors

Work out what you need for your project. Go to calculators and convertors

Contact us if you need your items quicker or need more than in stock.

Specifications

Weight 0.00000 kg
Dimensions 6.00 x 2.30 x 7.40mm
Maximum Resistance

Minimum Resistance

Package / Size

Power Rating

Product Type

, ,

Resistance Value

, ,

Series / Model

Temperature Coefficient

, ,

Temperature Range (°C)

Tolerance

, , , , ,

Alpha Resistor Videos

We are pleased to provide you with a range of videos, please see below for the latest content available:

 

 

VIDEOS
Place holder video for YouTube video Resistor Stability Put to the Test (Demo Video)

In this video, our host Richard Zuratt puts the stability of the three major resistor technologies — foil, thin, and thick film — to the test. Each resistor type is subjected to an overload pulse and its change in resistance value is recorded. Due to the homogeneous nature of the VPG Bulk Metal® Foil resistor, it is the only of the three to experience no change from the high power pulse. This demonstrated performance makes foil resistors the technology of choice for critical applications where long-term stability and survivability are paramount.

Place holder video for YouTube video Advantages of Using Bulk Metal® Foil Resistors in High-Humidity Environments

All resistors that are based on nichrome, which is a category that includes both thin film devices and Bulk Metal Foil resistors, are susceptible to electro-chemical corrosion or etching when placed in a high humidity environment and powered with a very low wattage. But since the nichrome element of a Bulk Metal Foil resistor is hundreds of times thicker than the element in a thin film device with the same value, it will last much longer under these conditions. This video shows the actual etching process and survival times for thin film and foil nichrome resistive elements as they are tested in 100% humidity conditions.

Place holder video for YouTube video Comparison Testing of Chip Resistor Technologies Under High Vibration

Surface-mount resistors suffer physical stresses when exposed to high vibration or thermally unstable environments. Failure modes commonly occur in welds, solder joints, connectors, and terminations, ultimately resulting in circuit failure. In this demonstration, vibration-table-mounted boards are subjected to ±2° deflection 25 times per second and monitored for any ΔR > 0.1%. All the chip resistors failed in 2 to 12 minutes (8K to 16K cycles). But the Alpha MPP molded Bulk Metal® Z-Foil resistor with flexible terminations experienced over a million cycles with no change in resistance.

VIDEOS
Place holder video for YouTube video
Resistor Stability Put to the Test (Demo Video

In this video, our host Richard Zuratt puts the stability of the three major resistor technologies — foil, thin, and thick film — to the test. Each resistor type is subjected to an overload pulse and its change in resistance value is recorded. Due to the homogeneous nature of the VPG Bulk Metal® Foil resistor, it is the only of the three to experience no change from the high power pulse. This demonstrated performance makes foil resistors the technology of choice for critical applications where long-term stability and survivability are paramount.

Place holder video for YouTube video
Advantages of Using Bulk Metal® Foil Resistors in High-Humidity Environments

All resistors that are based on nichrome, which is a category that includes both thin film devices and Bulk Metal Foil resistors, are susceptible to electro-chemical corrosion or etching when placed in a high humidity environment and powered with a very low wattage. But since the nichrome element of a Bulk Metal Foil resistor is hundreds of times thicker than the element in a thin film device with the same value, it will last much longer under these conditions. This video shows the actual etching process and survival times for thin film and foil nichrome resistive elements as they are tested in 100% humidity conditions.

Place holder video for YouTube video

Surface-mount resistors suffer physical stresses when exposed to high vibration or thermally unstable environments. Failure modes commonly occur in welds, solder joints, connectors, and terminations, ultimately resulting in circuit failure. In this demonstration, vibration-table-mounted boards are subjected to ±2° deflection 25 times per second and monitored for any ΔR > 0.1%. All the chip resistors failed in 2 to 12 minutes (8K to 16K cycles). But the Alpha MPP molded Bulk Metal® Z-Foil resistor with flexible terminations experienced over a million cycles with no change in resistance.

Alpha MD Series Resources

Product Datasheet

Supporting Product Information

Supporting Manufacturer Information

  • Energy
  • Alpha Electronics

Alpha MD Series

Please be advised that due to the ongoing supply issues with raw materials affecting the global electronics industry, as well as an increase in orders received by our manufacturing partners, a large number of products are facing increased lead times in recent months. For the latest lead time and stock availability, please contact one of our engineers who will be happy to discuss lead times further and the potential for alternative parts.