Design-Led Engineering Distributor

+44 (0) 1342 330 470

UL

Underwriters Laboratories® Inc. (UL) is an independent product safety certification organization Based in Northbrook, Illinois.

UL develops standards and test procedures for products, materials, components, assemblies, tools and equipment, chiefly dealing with product safety.

UL does not “approve” products. Rather it evaluates products, components, materials and systems for compliance to specific requirements, and permits acceptable products to carry a UL certification mark, as long as they remain compliant with the standards.

RARA ULV600

Metal clad wire wound resistor
Rated power 600W(Heatsink) / 330W (In air)
UL approved
Inductive or non-inductive design
Insulation resistance of 20MΩ minimum
Temperature range of -55°C up to +200°C
Option of flying leads, parallel or series connections

RARA ULV600

RARA ULV800

Metal clad wire wound resistor
Option of flying leads, parallel or series connections
Inductive or non-inductive design
Insulation resistance of 20MΩ minimum
Temperature range of -55°C up to +200°C
UL approved
Cement moulding with an extruded aluminium housing
Short time overload of 10 x power rating is 5 seconds

RARA ULV800

RARA ULV1000

Metal clad wire wound resistor
Option of flying leads, parallel or series connections
Inductive or non-inductive design
Insulation resistance of 20MΩ minimum
Temperature range of -55°C up to +200°C
UL approved
Cement moulding with an extruded aluminium housing
Short time overload of 10 x power rating is 5 seconds

RARA ULV1000

RARA ULV1200

Metal clad wire wound resistor
Option of flying leads, parallel or series connections
Inductive or non-inductive design
Insulation resistance of 20MΩ minimum
Temperature range of -55°C up to +200°C
UL approved
Cement moulding with an extruded aluminium housing
Short time overload of 10 x power rating is 5 seconds

RARA ULV1200

Stellar Technology LDP990 Series

Multipurpose clevis pin load cell with extra robust electrical connectors
Shock and vibration resistant
All welded stainless steel construction
Standard calibration is 5 points (0, 50%, 100%, 50%, 0) in both tension and compression
Temperature effect on zero ±0.008% FSO/°F
Temperature effect on span ±0.005% Reading/°F
Zero balance ±1% FSO

Stellar Technology LDP990

Weidmüller B2CF 3.50/180 Series

PCB terminal connector with 2 row female plug
Rated current for minimum number of poles 13.4A (IEC) and 9.5A (UL)
Dimensions of L1 3.5mm to 76.5mm (depending on the number of poles required)
Push in spring connection with integrated push buttons for opening the terminal point
Clamping range from 0.14mm² to 1.5mm²
Temperature range −50°C up to +120°C
CSA and UL 1059 approved, IEC listed

Weidmüller B2CF 3.50

Weidmüller BL 3.50/180 Series

Female plug in connector
Rated current for minimum number of poles 17A (IEC) and 10A (UL)
Dimensions of L1 3.5mm to 80.5mm (depending on the number of poles required)
Clamping yoke screw connection
Clamping range from 0.08mm² to 1.5mm²
Wire connection cross section from AWG 28 to AWG 14
Temperature range −50°C up to +100°C
CSA and UL 1059 approved, IEC listed

Weidmüller BL 3.50

Weidmüller BLF 2.50/180 Series

PCB terminal connector with female plug
Rated current for minimum number of poles 6A (IEC) and 5A (UL)
Dimensions of L1 2.5mm to 27.5mm (depending on the number of poles required)
Push in spring connection with integrated push buttons for opening the terminal point
Wire connection cross section from AWG28 (0.08mm²) to AWG 20 (0.5mm²)
Temperature range −40°C up to +105°C
CSA and UL 1059 approved, IEC listed

Weidmüller BLF 2.50

Weidmüller BLF 3.50/180 Series

Female plug in connector
Rated current for minimum number of poles 17.5A (IEC) and 10A (UL)
Dimensions of L1 3.5mm to 80.5mm (depending on the number of poles required)
Push in spring connection
Clamping range from 0.14mm² to 1.5mm²
Wire connection cross section from AWG 26 to AWG 16
Temperature range −50°C up to +120°C
CSA and UL 1059 approved, IEC listed

Weidmüller BLF 3.50

Weidmüller BLF 5.08HC/180 Series

High current female plug in connector
Rated current for minimum number of poles 24A (IEC) and 18.5A (UL)
Dimensions of L1 5.08mm to 116.84mm (depending on the number of poles required)
Clamping range from 0.13mm² to 3.31mm²
Wire connection cross section from AWG 26 to AWG 12
Temperature range −50°C up to +100°C
CSA and UL 1059 approved, IEC listed

Weidmüller BLF 5.08HC

Weidmüller BLZP 5.08HC/180 Series

High current female plug in connector
Rated current for minimum number of poles 23A (IEC) and 20A (UL)
Dimensions of L1 5.08mm to 116.84mm (depending on the number of poles required)
Clamping yoke screw connection
Clamping range from 0.13mm² to 4mm²
Wire connection cross section from AWG 30 to AWG 12
Temperature range −50°C up to +100°C
CSA and UL 1059 approved, IEC listed

Weidmüller BLZP 5.08HC

Weidmüller BUZ 10.16HP/180 Series

High power female plug in connector
Rated current for minimum number of poles 78.3A (IEC) and 60A (UL)
Dimensions of L1 10.16mm to 81.28mm (depending on the number of poles required)
Clamping range from 0.2mm² to 16mm²
Wire connection cross section from AWG 22 to AWG 6
Temperature range −50°C up to +130°C
CSA and UL 1059 approved, IEC listed

Weidmüller BUZ 10.16HP

Weidmüller BVF 7.62HP/180 Series

High power female plug in connector
Rated current for minimum number of poles 57A (IEC) and 39A (UL)
Dimensions of L1 7.62mm to 45.62mm (depending on the number of poles required)
Clamping range from 0.5mm² to 10mm²
Wire connection cross section from AWG 24 to AWG 8
Temperature range −50°C up to +125°C
CSA and UL 1059 approved, IEC listed

Weidmüller BVF 7.62HP

Weidmüller LLF 7.50/90V Series

PCB terminal connector
Rated current for minimum number of poles 41A (IEC) and 35A (UL)
Dimensions of L1 7.5mm to 82.5mm (depending on the number of poles required)
THT solder connection with a solder pin length of 5mm
Wire connection cross section from AWG 24 to AWG 8
Temperature range of −40°C to +120°C
CSA and UL 1059 approved, IEC listed

Weidmüller LLF 7.50

Weidmüller LLFS 7.50/180V Series

PCB terminal connector
Rated current for minimum number of poles 41A (IEC) and 37A (UL)
Dimensions of L1 7.5mm to 82.5mm (depending on the number of poles required)
THT solder connection with a solder pin length of 5mm
Wire connection cross section from AWG 24 to AWG 8
Temperature range of −40°C to +120°C
CSA and UL 1059 approved, IEC listed

Weidmüller LLFS 7.50

Weidmüller LM 3.50/90 Series

PCB terminal connector
Rated current for minimum number of poles 16A (IEC) and 10A (UL)
Dimensions of L1 3.5mm to 5mm (depending on the number of poles required)
SMT solder connection with a solder pin length of 3.2mm
Wire connection cross section from AWG 28 to AWG 14
Temperature range of −50°C to +120°C
CSA and UL 1059 approved, IEC listed

Weidmüller LM 3.50